Grip-Engineering info@grip.de		DIN Fixtures Back
DIN3-8 DIN EN3-8	Portable fire extinguishers - Part 8: Requirements for the construction, pressure resistance and mechanical tests for extinguishers with a maximum allowable pressure equal to or lower than 30 bar, which comply with the requirements of EN 3-7	THS1188
DIN34-1 DIN ISO34-1	Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 1: Trouser, angle and crescent test pieces	THS265-CW THS265-CHV12.7x102 Fig.2 THS1678
DIN71-1 DIN EN71-1	Safety of toys - Part 1: Mechanical and physical properties. (Tensile test).	TH124-20
DIN178 DIN EN ISO178	Plastics — Determination of flexural properties	TH103-B220-CR5-oFR5 TH103-3P-B220-AR2-5-oFR5-cgr TH103-3P-B220-AR3-5-oFR5-ok TH103-3P-B220-CR5-oFR5-cgr TH22 TH238
DIN267	Fasteners – Technical specification. Tensile strength testing.	THS144
DIN267-26	Technical delivery conditions for fasteners - Part 26: Conical spring washers for bolt/nut assemblies	THS2057
DIN302-3 DIN EN302-3	Adhesives for load-bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength	THS474-29-76-60-R12.5
DIN306 DIN EN ISO306	Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)	THS265
DIN310 DIN EN310	Wood-based panels; determination of modulus of elasticity in bending and of bending strength	THS930-20 TH22-3P-360-CX15-OX30 + ITH1 TH22-800-XO15x350-CXU15x350
DIN311 DIN EN311	Wood-based panels - Surface soundness - Test method	THS325-1
DIN314-1 DIN EN314-1	Plywood – bonding quality: part 1: test methods	THS1112-EN314-1
DIN319 DIN EN319	Particleboards and fibreboards; determination of tensile strength perpendicular to the plane of the board	TH16
DIN320 DIN EN320	Particleboards and fibreboards - Determination of resistance to axial withdrawal of screws	THS325-1 THS325-2
DIN388 DIN EN388	Protective gloves against mechanical risks	THS174-D20-F1V30-W130
DIN392 DIN EN392	Glued laminated timber - Shear test glue lines	TH17
DIN408 DIN EN408	Timber structures - Structural timber and glued laminated timber - Determination of some physical and mechanical properties	THS139-4P-2000-CX30x100-H200 TH22-4P-800-CWX30x300-Af318
DIN433 DIN EN433	Resilient floor coverings - Determination of residual indentation after static loading	TH23-11.28-Af159-ST
DIN455 DIN EN455	Medical Gloves for Single-Use	TH227
DIN488 DIN EN488	District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks.	THS260-150-500-D50-ORxx-Af6030
DIN488-2	Reinforcing steels - Reinforcing steel bars	THS290-1-3-16
DIN488-5	Reinforcing steels - Lattice girders. Shear test. Part 2.	THS290-1-3-16
DIN520 DIN EN520	Gypsum plasterboards - Definitions, requirements and test methods.	TH22-500-CWER5x300-oWER5x300 TH22-3P/4P-500-CWER3.2x305
DIN527-2 DIN EN ISO527-2	Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics	THS265-CW10x60 THS265-CHB10x60 (Type 1B) THS265-CHB10x80 (Type 1A) THS265-CHB4x25 (Type 5A) THS265-CHB5x30 (Type 1BA) THS265-CHB2x12-4x30 (Type 1BB) THS265-CHB2x12-6x35 (Type 5B) THS474-10-H10-R25 THS1390-ISO527-2-Type1A
DIN527-3 DIN EN ISO527-3	Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets	THS265-CHB6x33 (Type 5) THS265-CHB10x60 (Type 1B) THS265-CHB25.4x50 (Type 4) THS265-CHR15x150 (Type 3) THS474-10-R60
DIN582 DIN EN582	Thermal spraying; determination of tensile adhesive strength	THS625
DIN604 DIN EN ISO604	Plastics - Determination of compressive properties	TH23-56 THS1390-ISO604-Type B
DIN763	Tested, non-calibrated, long-link round steel chains	THS573-20
DIN789 DIN EN789	Timber structures - Test methods - Determination of mechanical properties of wood based panels	THS1451 THS674
DIN813 DIN ISO813	Determination of adhesion to a rigid substrate - 90 degree peel method	TH95-3 TH95-4
DIN826 DIN EN826	Thermal insulating products for building applications - Determination of compression behaviour	TH36-400-L6x20 THS223k+TH36-100-oZR-Am317-AL
DIN843-1-1 DIN EN843-1-1	Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 1: Determination of flexural strength	TH238-3P/4P-ASTM-C1161-Af159
DIN844 DIN EN ISO844	Rigid cellular plastics — Determination of compression properties	TH23-156-St + THS223g-156
DIN863 DIN EN863	Protective clothing - Mechanical properties - Test method: Puncture resistance	THS174-D20-F1V30-W130
DIN868-5 DIN EN868-5	Packaging for terminally sterilized medical devices - Part 5: Sealable pouches and reels of porous materials and plastic film construction	THS1217-V41 + TH240k-Ko+BP30
DIN898-1 DIN EN ISO898-1	Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes -- Coarse thread and fine pitch thread	THS659-1000 THS786
DIN898-2 DIN EN ISO898-2	Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread	THS786-70 (tensile test) THS659 (tensile test) THS910 (compression test)
DIN969	Threaded fasteners - Axial load fatigue testing - Test methods and evaluation of results	THS659-250-10xM14-TK120
DIN1170-4 DIN EN1170-4	Precast concrete products - Test method for glass-fibre reinforced cement - Part 4: Measuring bending strength; "simplified bending test" method	TH103-4P-330-CWEX10-EN1170-4
DIN1193	Steel hammers - Technical specifications	THS162-910 + TH224+BV
DIN1279-4 DIN EN1279-4	Glass in building - Insulating glass units - Part 4: Methods of test for the physical attributes of edge seal components and inserts	THS504
DIN1288-3 DIN EN1288-3	Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four point bending)	THS124-V2-700
DIN1288-5 DIN EN1288-5	Glass in building - Determination of the bending strength of glass - Part 5: Coaxial double ring test on flat specimens with small test surface areas	THS747-EN1288-5
DIN1293 DIN EN1293	General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers	THS828-100-4P-30x160
DIN1324 DIN EN1324	Adhesives for tiles - Determination of shear adhesion strength of dispersion adhesives	THS450 THS534
DIN1348 DIN EN1348	Adhesives for tiles - Determination of tensile adhesion strength for cementitious adhesives	TH36-50
DIN1372 DIN EN1372	Test method for adhesives for floor and wall coverings - Peel test	TH192-D20-A26-W57-H38
DIN1400 DIN EN1400	Child use and care articles - Soothers for babies and young children - Safety requirements and test methods (includes Amendment :2018)	THS1088 + TH230 THS1088-60 (Pacifier Test Fixture)
DIN1464 DIN EN1464	Adhesives - Determination of peel resistance of adhesive bonds - Floating roller method	TH105-D25-B30 TH105-D30-W45-Af20
DIN1465 DIN EN1465	Adhesives - Determination of tensile lap-shear strength of bonded assemblies	TH11-5 TH256
DIN1607 DIN EN1607	Thermal insulating products for building applications - Determination of tensile strength perpendicular to faces	TH113 TH16
DIN1608 DIN EN1608	Thermal insulating products for building applications - Determination of tensile strength parallel to faces	THS170-500-S200
DIN1719 DIN EN1719	Adhesives for paper and board, packaging and disposable sanitary products - Tack measurement for pressure sensitive adhesives - Determination of loop tack	THS864-10
DIN1806 DIN EN ISO1806	Fishing nets - Determination of mesh breaking force of netting	TH231 TH231-6-16 THS43
DIN1922 DIN EN ISO1922	Determination of shear properties	TH193-V4
DIN1927-6 DIN EN ISO1927-6	Monolithic (unshaped) refractory products - Part 6: Measurement of physical properties. 6. Determination of cold crushing strength.	THS223-196 + TH23-196 (for insulating unshaped materials) THS223-96 + TH23-196 (for dense unshaped materials)
DIN1939 DIN EN1939	Self adhesive tapes - Determination of peel adhesion properties	TH50 TH49 THS989-95x45-HR THS1864
DIN19736
DIN2039-1 DIN EN ISO2039-1	Plastics - Determination of hardness - Part 1: Ball indentation method	THS265
DIN2137 DIN ISO2137	Rigid cellular plastics — Determination of tensile properties	THS1010-10
DIN-DVS2203-5	Testing of welded joints of thermoplastics plates and tubes - Technological bend test	THS260-100-360-D50-OR12.5-Af20
DIN2243-2 DIN EN2243-2	Petroleum products and lubricants - Determination of cone penetration of lubricating greases and petrolatum	TH105-D25-B30
DIN2243-3	Aerospace series - Non-metallic materials - Structural adhesives - Test method - Part 3: Peeling test metal-honeycomb core	TH115
DIN2243-4 DIN EN2243-4	Aerospace series - Non-metallic materials - Structural adhesives - Test method - Part 4: Metal-honeycomb core flatwise tensile test	TH113
DIN2377 DIN EN2377	Aerospace series; glass fibre reinforced plastics; test method; determination of apparent interlaminar shear strength	THS884+TH238
DIN2439 DIN EN ISO2439	Flexible cellular polymeric materials — Determination of hardness (indentation technique)	TH36-D200-R1+THS223b-Af159
DIN2493-1 DIN ISO 2493-1	Paper and board - Determination of bending resistance - Part 1: Constant rate of deflection	THS1445-V3
DIN2562 DIN EN2562	Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates; flexural test parallel to the fibre direction	THS884-ith2-Af159 TH238-AR3+OR3+THS884 TH103-B220-CR3-5-oFR3-oFR12.5-ok+GDE
DIN2563 DIN EN2563	Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates; determination of apparent interlaminar shear strength	TH103-B220-CR3-5-oFR3-oFR12.5-ok+GDE TH238-AR3+OR3+THS884 TH238St-AR3x3-OR3+Gde THS884+TH238+TH187
DIN3037 DIN EN ISO 3037	Corrugated fibreboard — Determination of edgewise crush resistance (unwaxed edge method)	THS733-200-ISO3037 THS86-150x220-H127
DIN3303-1 DIN EN ISO3303-1	Bursting strength of rubber- or plastics-coated fabrics - Part 1: Steel-ball method	THS453-45-P25.2
DIN3327 DIN EN ISO3327	Hardmetals - Determination of transverse rupture strength	THS1087 TH22St-240-CX5-cgr TH22St-360-CX6-oX6
DIN3377- 2 DIN EN ISO3377- 2	Leather - Physical and mechanical tests - Determination of tear load - Part 2: Double edge tear	THS694-20-L80-Af159-2L THS694-20-L98-Af159-2L
DIN3379 DIN EN ISO3379	Leather - Determination of distension and strength of surface (Ball burst method)	THS460
DIN3386-1 DIN EN ISO3386-1	Polymeric materials, cellular flexible - Determination of stress-strain characteristics in compression - Part 1: Low-density materials	THS223k-D203 TH36L-L6x20
DIN3651-2 DIN EN ISO3651-2	Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid	TH103-FV-oFR2,3,4,5-W70
DIN3781 DIN ISO3781	Paper and board -- Determination of tensile strength after immersion in water	THS779-5x60
DIN4108-11	Thermal insulation and energy economy in buildings - Part 11: Minimum requirements to the durability of bond strength with adhesive tapes and adhesive masses for the establishment of airtight layers	THS1217-V40 (T-peel test) TH49 (180° peel test)
DIN4226-1	Aggregates for concrete and mortar - Part 1: Normal and heavy-weight aggregates	THS994
DIN4226-2	Aggregates for concrete; aggregates of porous structure (lightweight aggregates); terminology, designation and requirements	THS994
DIN4624 DIN EN ISO4624	Paints and varnishes, pull off test for adhesion	THS625 THS1514
DIN4843	Safety footwear; safety requirements, testing	TH124-20
DIN5173 DIN EN ISO5173	Destructive tests on welds in metallic materials - Bend tests	THS1018 THS260
DIN5299	Snap hook Karabinerhaken	THS573-20
DIN6259-3 DIN EN ISO6259-3	Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes	THS1086-12-50 THS1086-30-70
DIN6507-2 DIN EN ISO6507-2	Metallic materials - Vickers hardness test - Part 2: Verification and calibration of testing machines	THS71-10
DIN6872 DIN EN ISO6872	Dentistry - Ceramic materials	THS1620-16.5-1.6-ISO6872 TH238-5P-CWX5-Af159
DIN6892 DIN EN ISO 2	Metallic materials - Tensile testing - Part 1: Method of test at room temperature	THS265-CSB12.5x75-20x175 (Type 1) THS265-CSB20x90-32x210 (Type 2) THS265-CSB20x80-30x180 (Type 1) THS265-CSB20x120-30x270 (Type 1)
DIN6899	Steel thimbles for fibre ropes Kauschen aus Stahl für Fasereile	THS573-40
DIN7389 DIN EN ISO7389	Building construction - Jointing products - Determination of elastic recovery of sealants	THS504
DIN7438 DIN EN ISO7438	Metallic materials — Bend test	TH238-3P-200-CXD30x40 TH103-FV-VDA238-100 THS260 THS1711
DIN7808 DIN EN ISO7808	Plastics - Thermosetting moulding materials - Determination of transfer flow	TH4220-D90+gde
DIN 7864 DIN EN ISO7864	Tensile test fixture to test sterile hypodermic needles	THS1114 THS1180
DIN7886-1 DIN EN ISO7886-1	Sterile hypodermic syringes for single use - Part 1: Syringes for manual use	THS727-80 TH238-ISO9626
DIN8295 DIN EN ISO8295	Plastics - Film and sheeting - Determination of the coefficients of friction	TH62-50
DIN8339 DIN EN ISO8339	Building construction - Sealants - Determination of tensile properties (Extension to break)	THS504
DIN8340 DIN EN ISO8340	Determination of tensile properties at maintained extension	THS504-52-12-77-36-5
DIN8493 DIN EN ISO8493	Metallic materials - Tube - Drift-expanding test	THS791
DIN8895 DIN EN ISO 8895	Shaped insulating refractory products - Determination of cold crushing strength	THS223-196 + TH23-196
DIN9046 DIN EN ISO9046	Building construction - Jointing products - Determination of adhesion/cohesion properties of sealants at constant temperature	THS504
DIN9073-5 DIN EN ISO9073-5	Textiles - Test methods for nonwovens - Part 5: Determination of resistance to mechanical penetration (ball burst procedure)	THS453-D44.45-R12.7
DIN9073-7 DIN EN ISO9073-7	Textiles - Test methods for nonwovens - Part 7: Determination of bending length	THS853-20
DIN9073-18 DIN EN ISO9073-18	Textiles — Test methods for nonwovens — Part 18: Determination of breaking strength and elongation of nonwoven materials using the grab tensile test	TH83+BG25
DIN9187-1 DIN EN ISO9187-1	Injection equipment for medical use - Part 1: Ampoules for injectables	TH238-B200-OR2-CWx TH238-ISO9187-1
DIN9626 DIN EN ISO9626	Stainless steel needle tubing for the manufacture of medical devices - Requirements and test methods	THS1588-ISO9626-Ann.C TH238+CR0.1V90-OR1-St
DIN9665 DIN EN ISO 9665	Adhesives - Animal glues - Methods for sampling and testing	THS42-F12.7R0.39-80 + TH23-56
DIN9836-1 DIN EN ISO9836-1	Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers	THS1597
DIN10080 DIN EN10080	Steel for the reinforcement of concrete - Weldable reinforcing steel - General	THS162-1060-V3-EN10080
DIN10130 DIN EN10130	Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions	TH192-20-26-W60
DIN10223-3 DIN EN10223-3	Steel wire and wire products for fencing and netting - Part 3: Hexagonal steel wire mesh products for civil engineering purposes	TH43-G40+W630
DIN10223-8 DIN EN10223-8	Steel wire and wire products for fencing and netting - Part 8: Welded mesh gabion products	THS290-40
DIN10319 DIN EN ISO10319	Geosynthetics - Wide-width tensile test	TH135 THS668
DIN10354 DIN EN ISO10354	Adhesives – Characterization of durability of structural-adhesive-bonded assemblies – Wedge rupture test	THS1455-CH6.5x1-P3x25V60
DIN10477 DIN EN ISO10477	Dentistry - Polymer-based crown and veneering materials	TH238+CX2+4+10 THS1680-V2-20x6
DIN10545 DIN EN ISO10545	Ceramic tiles - Part 2: Determination of dimensions and surface quality	TH22-360
DIN11542-2 DIN EN ISO11542-2	Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties	THS941
DIN11600 DIN EN ISO11600	Building construction - Jointing products - Classification and requirements for sealants	THS504
DIN11608-3 DIN EN ISO11608-3	Needle-based injection systems for medical use - Requirements and test methods - Part 3: Finished containers	THS1256-V1
DIN11644 DIN EN ISO11644	Leather - Test for adhesion of finish	THS1186-20
DIN11979-3 DIN EN ISO11979-3	Ophthalmic implants - Intraocular lenses - Part 3: Mechanical properties and test methods. Compression test.	THS1468
DIN12002 DIN EN12002	Adhesives for tiles - Determination of transverse deformation for cementitious adhesives and grouts	TH238-B300-CXH50-D10x60 THS763
DIN12003 DIN EN12003	Adhesive for tiles - Determination of shear adhesion strength of reaction resin adhesives	THS450 THS534
DIN12004 DIN EN12004	Adhesives for tiles - Requirements, evaluation of conformity, classification and designation	TH16 THS450
DIN12089 DIN EN12089	Thermal insulating products for building applications - Determination of bending behaviour	TH22-1300-CX80x300-EN12089-A TH22-600-CX30x150- EN12089-B
DIN12090 DIN EN12090	Shear properties of sandwich core materials	TH193-V4 (Fig. 1) THS608
DIN12190 DIN EN12190	Determination of compressive strength of repair mortar	TH103-220-CWX10-OWX10
DIN12192 DIN EN ISO12192	Paper and board — Determination of compressive strength — Ring crush method	THS733-200-ISO12192
DIN12230 DIN EN12230	Surfaces for sports areas. Determination of tensile properties of synthetic sports surfaces	THS265-CH25x55
DIN12236 DIN EN ISO12236	Static puncture test on geotextiles	THS174-D150-F50-V2
DIN12242 DIN EN12242	Touch and close fasteners - Determination of peel strength	THS989-100-5-HR
DIN12259-1 DIN EN12259-1	Fixed firefighting systems - Components for sprinkler and water spray systems - Part 1: Sprinklers	THS1730-V1
DIN12310-1 DIN EN12310-1	Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing; determination of resistance to tearing (nail shank).	THS716
DIN12311-2 DIN EN12311-2	Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing	THS265-CHB6x33(Type B) TH154-10+BP
DIN12372 DIN EN12372	Natural stone test methods - Determination of flexural strength under concentrated load	TH103-300-CWX10
DIN12402-Fig1 DIN EN ISO12402-Fig1	Standard for personal flotation devices	THS1205-9x1.6-Af20
DIN12430 DIN EN12430	Thermal insulating products for building applications - Determination of behaviour under point load	TH23-79.8 TH36-300-QZ100-Al + THS223k-79.8R0.5-Af159
DIN12431 DIN EN12431	Thermal insulating products for building applications. Determination of thickness for floating floor insulating products	TH36-200
DIN12467 DIN EN12467	Fibre-cement flat sheets - Product specification and test methods	TH22-360+FD30x250 TH22St-5P-800-CWX10+CWX40x500+CWLD30x120
DIN12625-5 DIN EN ISO12625-5	Tissue paper and tissue products - Part 5: Determination of wet tensile strength	THS779-2020-HL
DIN12625-9 DIN EN ISO12625-9	Tissue paper and tissue products - Part 9: Determination of ball burst strength	THS855-10
DIN12773 DIN EN12773	Footwear - Test methods for outsoles - Needle tear strength	THS111-DIN53506-Af159-P
DIN12814-2 DIN EN12814-2	Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test	THS260-100-360
DIN12814-4 DIN EN12814-4	Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test	THS353-5x30 (Fig.5 )
DIN13055-1 DIN EN13055-1	Lightweight aggregates - Part 1: Lightweight aggregates for concrete, mortar and grout	THS994
DIN13354 DIN EN13354	Solid wood panels (SWP) - Bonding quality	THS740
DIN13393 DIN EN13393	Packaging - Specification for edge protectors	THS993-240
DIN13446 DIN EN13446	Wood-based panels - Determination of withdrawal capacity of fasteners	THS325+THS235-20-130x130
DIN13494 DIN EN13494	Thermal insulation products for building applications - Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material	THS235-60x60-132x132
DIN13503-2 DIN EN ISO13503-2	Petroleum and natural gas industries -- Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations	THS947
DIN13523-1 DIN EN13523-1	Coil coated metals - Test methods - Part 1: Film thickness	TH4060
DIN13555 DIN EN13555	Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections	THS1510
DIN13572 DIN EN13572	Footwear - Test methods for uppers, lining and insocks - Seam strength	THS1205
DIN13892-2 DIN EN13892-2	Methods of test for screed materials - Part 2: Determination of flexural and compressive strength	TH103-200-CWEX10-OWEX10
DIN13934 DIN EN ISO13934	Textiles - Tensile properties of fabrics - Part 1: Determination of maximum force and elongation at maximum force using the strip method	TH83 THS265-CHR50x260
DIN13936-1 DIN EN ISO13936-1	Textiles - Determination of the slippage resistance of yarns at a seam in woven fabrics - Part 1: Fixed seam opening method	TH240g+B25x25+B25x50
DIN13936-2 DIN EN ISO13936-2	Textiles - Determination of the slippage resistance of yarns at a seam in woven fabrics - Part 2: Fixed load method	TH240g+BP25x25+BP25x50 TH240k+BW30+BW50
DIN13936-3 DIN EN ISO13936-3	Textiles - Determination of the slippage resistance of yarns at a seam in woven fabrics - Part 3: Needle clamp method	THS1108
DIN14024 DIN EN14024	Metal profiles with thermal barrier. Mechanical performance. Requirements, proof and tests for assessment	THS1273 (Tensile test) THS674-V4 (Shear test)
DIN14080 DIN EN14080	Timber structures - Glued laminated timber and glued solid timber - Requirements Timber structures - Glued laminated timber and glued solid timber - Requirements	TH17
DIN14125 DIN EN ISO14125	Fibre-reinforced plastic composites - Determination of flexural properties	TH22-5P-240-CWLD4+D10 TH22-5P-CWR2+110 Fig 4 THS884+TH238+TH187 THS1498-5P-300-R2+R5-Af159
DIN14126 DIN EN ISO14126	Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction	TH121 THS613 (Method 1) THS705+Ko (Method 2) THS321-250c-Hy + THS705-F100-Ko (Method 2) THS793-ISO14126 (Method 2 Fig. C2)
DIN14130 DIN EN ISO14130	Fibre reinforced plastic composites - Determination of apparent interlaminar shear strength by short beam-method	TH103-B220+AR2R5 THS884-ith2-Af159 THS1498-5P-300-R2+R5-Af159
DIN14272 DIN EN ISO14272	Resistance welding - Destructive testing of welds - Specimen dimensions and procedure for cross tension testing of resistance spot and embossed projection welds	THS1146
DIN14279 DIN EN14279	Laminated Veneer Lumber (LVL) - Definitions, classification and specifications	THS927
DIN14410 DIN EN14410	Self adhesive tapes - Measurement of breaking strength and elongation at break	THS919-100 THS919-100-100-F20
DIN14444 DIN EN14444	Structural adhesives - Qualitative assessment of durability of bonded assemblies - Wedge rupture test	THS1455-CH6.5x1-P3x25V60
DIN14566 DIN EN14566	Mechanical fasteners for gypsum plasterboard systems - Definitions, requirements and test methods	TH235-20-150x150
DIN14704-1 DIN EN14704-1	Determination of the elasticity of fabrics - Part 1: Strip tests	TH231 (Loop test) THS353-6x80-Al (Loop test) TH240g+BLCR3-25x75 (Strip test) TH227-B80-BLCR3 (Strip test)
DIN14477 DIN EN14477	Packaging, Flexible packaging material - Determination of puncture resistance - Test methods	THS511 THS42-R0.5-50-Af159
DIN14509 DIN EN14509	Self-supporting double skin metal faced insulating panels - Factory made products - Specifications	TH22-1300-500-CN40x200 TH22-1000-360-CM60x160-H200 THS1063-20.3-WDF
DIN14555 DIN EN ISO14555	Welding - Arc stud welding of metallic materials	THS1556
DIN14801 DIN EN ISO14801	Dentistry - Implants - Dynamic loading test for endosseous dental implants	THS543-170 THS1959
DIN14891 DIN EN14891	Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, assessment and verification of constancy of performance, classification and marking	THS1168-Am1665
DIN14916 DIN EN ISO14916	Thermal spraying - Determination of tensile adhesive strength	THS625 THS1514
DIN15048-1 DIN EN15048-1	Non-preloaded structural bolting assemblies - Part 1: General requirements	THS786
DIN15630-2 DIN EN ISO15630-2	Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded fabric and lattice girder	THS290-10 THS290-21 THS290-30 THS290-40 THS290-50
DIN CEN/TR 16792-Fig.B5	Safety of children's clothing - Recommendations for the design and manufacture of children's clothing - Mechanical safety. Button pull-off test	THS807-S25 + THS1042-30 THS1042-10 + TH240k+BP25+BP50
DIN17271 DIN EN17271	Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the peel strength of profiles laminated with foils	TH192-25-27-180-180-4R
DIN17333-4 DIN EN17333-4	Characterization of One Component Foam (OCF) - Part 1: Yield Measurement of the tensile strength of polyurethane foam Charakterisierung von Einkomponentenschäumen Messung der Zugfestigkeit von Polyurethanschaum	THS504-62-82-200-5-Af20-EN17333-4-M2
DIN17697 DIN EN ISO17697	Footwear - Test methods for uppers, lining and insocks - Seam strength	THS1205
DIN18134	Soil - Testing procedures and testing equipment - Plate load test	TH4020
DIN18164-1	Cellular plastics as insulating building materials; insulating materials thermal insulation	THS170
DIN19304	Testing of corrugated board-Creasings	THS1489-V2 THS1489-V3
DIN19736 DIN ISO19736	Dentistry - Bonding test between polymer teeth and denture base materials	THS1959-ISO19736
DIN20126 DIN EN ISO20126	Dentistry — Manual toothbrushes — General requirements and test methods	THS341-10-K + THS63-10
DIN20482 DIN EN ISO20482	Testing of metals; Erichsen cupping test on sheet and strip metal having a width of >= 90 mm; Thickness range: 0.2 mm to 2 mm	THS145-D27-R10 THS145-D11-R4
DIN20795-1 EN ISO20795-1	Dentistry - Artificial teeth for dental prostheses	THS1447-S12 + TH227+BP25-Af20
DIN21182 DIN EN ISO21182	Light conveyor belts - Determination of the coefficient of friction	TH62-40
DIN22112 DIN EN ISO22112	Dentistry - Artificial teeth for dental prostheses	THS1447-S12 + TH227+BP25-Af20
DIN22254 DIN EN ISO22254	Dentistry - Manual toothbrushes - Resistance of tufted portion to deflection	THS63
DIN23910 DIN EN ISO23910	Leather - Physical and mechanical tests - Measurement of stitch tear resistance	THS694-10
DIN23936-2-B.2 DIN EN ISO23936-2-B.2	Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 2: Elastomers	THS1512-325
DIN24343 DIN EN ISO24343	Resilient and laminate floor coverings — Determination of indentation and residual indentation	TH23-11.28-Af159-ST THS42-F11.3-125-Af159
DIN28510-1 DIN EN28510-1	Adhesives - Peel test for a flexible-bonded-to-rigid test specimen assembly - Part 1: 90° peel	TH50
DIN29022 DIN EN ISO29022	Dentistry - Adhesion - Notched-edge shear bond strength test	THS633-540-V5
DIN29862 DIN EN ISO29862	Self adhesive tapes - Determination of peel adhesion properties	THS989-95x45-HR TH49 TH50 (90° peel test)
DIN40802-1	Metal-clad base material for printed circuits;specifications	TH249-12-25
DIN50101-1	Testing of metals; Erichsen cupping test on sheet and strip metal having a width of >= 90 mm; Thickness range: 0.2 mm to 2 mm	THS145-D27-R10
DIN50101-2	Testing of metals; Erichsen cupping test on sheet and strip metal having a width of >= 90 mm; Thickness range: over 2 mm up to 3 mm	THS145-D40-R10
DIN50109	Tensile testing of lamellar graphite cast iron	TH179-63-8
DIN50114	Testing of metals; tensile test on sheet or strip without using an extensometer	TH135
DIN50125	Testing of metallic materials - Tensile test pieces	THS800-120 TH89-20 TH89-3816 THS565-60 THS474-12.5x20 THS885-70 THS265-CSB12.5x75-20x165 THS265-CSB20x60-27-100
DIN50141	Testing of metals; Shear test	THS396
DIN50146 DIN EN50146	Cable ties for electrical installations	THS43-H40
DIN50139	Testing of Steel; Flanging Test on Tubes	THS791-A60xD148-Af6025 + TH23
DIN50342-5 DIN EN50342-5	Lead-acid starter batteries - Part 5: Properties of battery housings and handles	THS1402 (4.4.4)
DIN52186	Testing of wood- Bending test	TH22-WNJ30
DIN52187	Testing of wood; determination of ultimate shearing stress parallel to grain	THS740 TH17
DIN52292-1	Testing of glass and glass ceramics; determination of bending strength; coaxial double ring bending test on flat specimens with small test area	THS747-30-90-R2.5-DIN52292-Am1665 +THS800-200x200x150
DIN52352	Testing of wood fibre boards; bend testing	TH22-1200-CJ50x120
DIN52365	Testing of wood chipboards; determination of tensile strength vertical to the chipboard plane	TH16
DIN52367	Wood-based panels - Determination of shear strength parallel to the surface	TH17
DIN52371	Testing of plywood; bending test	TH22
DIN52377	Testing of plywood - Determination of modulus of elasticity in tension and of tensile strength	TH83
DIN52455-3	Testing of sealants in building construction - Adhesion and extension test - Part 3: Influence of light through glass	THS504
DIN53121	Testing of paper and board - Determination of the bending stiffness by the beam method	THS1119 (4-Point) THS1478 (1-Point) THS1489-V2 (1-Point, bending angle)
DIN53142-2	Testing of board - Puncture test - Part 2: Puncture test with linear move	THS174-Tr100-Pr60x25
DIN53278	Testing of adhesives for floor coverings; testing of peel-resistance of bondings, reaction adhesives for rubber floor-coverings described in DIN 16852	TH249-12-25
DIN53289	Rollenschälversuch	TH105-D25-B30
DIN53292	Testing of sandwiches; Tensile test perpendicular to the faces	TH113
DIN53293	Testing of sandwiches; Bending test	TH22-4P-700-CX30-CR2 TH22-5P-CWR2+110 Fig 4
DIN53294	Shear properties of sandwich core materials	TH193-V6
DIN53295	Peel resistance of adhesive bonds, e.g. for honeycomb sandwich constructions	TH115
DIN53331	Leather - Measurement of stitch tear resistance	THS694-10
DIN53357	Testing of plastics sheets; adhesion test	TH3-90
DIN53362	Testing of plastics films and textile fabrics (excluding nonwovens), coated or not coated fabrics - Determination of stiffness in bending - Method according to Cantilever	THS853-20
DIN53363	Determining the tear resistance of plastic film and sheeting by the trouser tear method	THS265-CWS50x120 (cutting die)   TH240k+BG80  (grip)
DIN53375	Testing of plastic film and sheeting; determination of the coefficients of friction	TH62-F
DIN53399	Testing of reinforced plastics; shear test on plane specimens	THS932
DIN53430	Testing of Rigid Cellular Materials; Tensile Test	TH213
DIN53494	Electroplated coatings; testing of electroplated plastic articles; determination of peel strength	TH104-30
DIN53504	Testing of rubber - Determination of tensile strength at break, tensile stress at yield, elongation at break and stress values in a tensile test	TH44 THS265-CW THS265-CHB4x16 (S3) THS265-CHB4x25 (S2) THS265-CHB2x12-6x35 (S3) THS265-CHB6x33
DIN53506	Testing of rubber; determination of needle tear resistance	THS111-DIN53506-Af159-P
DIN53530	Testing of organic materials; Separation test on fabric plies bonded together	TH3-25-S-Af159
DIN53515	Determination of tear strength of rubber elastomers and plastic film using Graves angle test piece with nick	THS265-CW THS265-CHV12.7x102
DIN53531-1	Determination of the adhesion of rubber to rigid materials by the one-plate method	TH95-3 TH95-4
DIN53579-2	Testing of flexible cellular materials; hardness test on finished parts; compression test on profiles	THS223b-112.8 TH36L-160 + THS223b + THS42
DIN53769-1	Testing of glass fibre reinforced plastics pipes; determination of the longitudinal shear strength of type B pipe fittings	THS1709
DIN53857	Testing of textiles; simple tensile test on strips of textile fabrics, woven fabrics and ribbons	TH83
DIN53858	Testing of textiles; determination of the breaking strength of textile fabrics (with the exception of nonwoven textiles), grab method	TH83
DIN53864	Testing of textiles; determination of the bending strength	THS1445-V5
tDIN54307 (superseded by ISO12236)	Testing of geotextiles and geotextile related products; static puncture test (CBR) (proposal for a European Standard)	THS174-150
DIN54516	Testing of paper and board - Determination of plybond resistance	THS87-30
DIN60793-1-32 DIN EN/IEC 60793-1-32	Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability	THS1192+Ko + TH76-1-D80+Ko
DIN61061-1 DIN EN61061-1	Non-impregnated densified laminated wood for electrical purposes - Part 1: Definitions, designation and general requirements	THS949
DIN61386-1 DIN EN61386-1	Conduit systems for cable management - Part 1: General requirements	TH16-99-D64-W100 (Tensile test) TH23-Q50-R1-Af20-ST (Compression test)
DIN65380	Aerospace; fibre reinforced plastics; testing of unidirectional laminates and woven-fabric laminates; compression test	TH121
DIN65561	Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of compressive strength after impact test	THS818
DIN68501	Hardware for furniture - Test methods for determination of strength and stiffness of cabinet connectors	THS1576
info@grip.de LX 04 Nov 2025		TOP